Spare parts Citroën Ami 6, Ami 8

The 123 Ignition electronic igniter is specially designed for the Citroën 2CV, Dyane, Ami and Mehari.
This igniter allows you to optimize the performance and reliability of your Citroën!The igniter is designed to work with Citroën's original (black) ignition coil, and is compatible with both 6- and 12-volt vehicles.
This igniter allows you to select the right ignition curve for your Citroën from a choice of 16 different curves to suit your engine.
It is compatible with the following engine types and chassis by selecting the right curve:- 9 hp 375cc type A -> curve 1- A53 type AZ -> curve 2- M4 type AM -> curve 3- A79/0 type AYA -> curve 4- M28 type AM2 -> curve 5- A79/1 type AYA2-> curve 6- M28/1 -> curve 7(AK2), 8(A06/635), 9(A06/642), A(AM2A), B(A06/664) and F(bio-ethanol E85 conversion)

This dry coil for Citroën AMI6 and AMI8 - 12V features a technology that avoids the use of traditional oil bath cooling.
Much more reliable, and avoiding the leaks of a traditional 2cv ignition coil, it is essential that you use an electronic ignition while remaining compatible with a classic ignition by means of a capacitor and platinum screws.

Offering high performance, the dry coil produces increased ignition voltage, and superior spark power to the spark plugs.

This dry coil is compatible with all derivatives of the 12V 2CV:
- 2CV
- Mehari
- Dyane/Acadiane
- AMI6 and AMI8

This Electronic 12V DG NITION Ignition for AMI6 and AMI8 (10/1968-07/1987) is the easiest to install.


Compatible with 2cv and derivatives with 12V electric circuit with A79/1, M28, M28/1 motors, this Electronic Ignition for AMI6 and AMI8 is simple, reliable and powerful.
It will metamorphose your vehicle's driving and maintenance.
- no more platinum screw adjustments
- no more capacitors snapping
- easier hot and cold starting
- more stable idle
- reduced fuel consumption
- wider torque range.

This BRETILLE displacement kit for 602cc M28 engines in AMI6 and AMI8 cars - compression 9 is original quality.

Made in France, this set of piston liners for 2cvs from BRETILLE is compatible with all AMI 6 and AMI 8 cars with M28 602cc engines.
Its high compression, originally intended for utility vehicles and heavier AMI's, gives it more torque than its lower compression counterpart.

It includes the 2 liners, the 2 pistons and the piston rings already fitted in the factory.

This single body carburettor for AMI 6 and AMI 8 - 34 PICS is a remake of the Solex 34PICS6 mounted on AMI 6 and AMI 8 from 1972.

Supplied with its baseplate gasket, this carburettor is pre-tuned from the factory, but its final adjustment will have to be carried out on a hot engine.
We recommend that you replace the spacer, fuel filter and air filter at the same time for optimum performance.

The carburettor seals and diaphragms are not compatible with SP95-E10 petrol, the use of an additive will avoid any premature deterioration.

This Dual Body Carburetor for AMI 8 - 26-35 CSIC with Assist Vacuum Pump is a remanufacture of the Solex 26/35 CSIC fitted to 2cv's and derivatives from 1978 onwards.

Supplied with its base gasket, this Carburetor for AMI8 is factory pre-tuned, but its final tuning will be required on a warm engine.
It is strongly advised to replace its spacer, fuel filter and air filter at the same time for optimal operation.

The seals and diaphragms of this carburetor are not compatible with SP95-E10 gasoline, the use of an additive is necessary to avoid premature deterioration.

This carburetor is not suitable for vehicles with centrifugal clutch.

This complete kit of gaskets and pins for SOLEX 26-35 CSIC dual barrel carburettor for AMI6 and AMI8 contains everything you need to rebuild a SOLEX 26-35 CSIC carburettor.

All gaskets and diaphragms are present in this solex 26-35 carburettor rebuild kit, as well as new screws, jets and needles. Please note that you will find 2 tank seals depending on whether your vehicle has a centrifugal clutch or not. Keep your old tank gasket when disassembling and only reassemble the right one.

The repair of a carburettor is not complicated but it requires method and patience as well as a meticulous cleaning of each element of the latter.
A tip: take pictures of each step of the disassembly.

This bag of 50 elasticated seat bands for AMI 6 and AMI 8 cars is compatible with all models.


This bag of 50 elasticated bands contains the quantity you need to repair a seat. You will need 2 of them for a complete bench seat repair.

Installation tips:
- Prepare the burlap or reinforced seat cloths by spreading the fibres evenly with a pointed object or a simple nail, opposite the holes in the frame.
- Mount the elastics symmetrically, one on the right and one on the left, to make it easier for you to mount them on the frame. If you mount one side first, it will be very difficult to mount the other.

This fuel pump for AMI8 from 1970 is compatible with all 2cvs and their derivatives with 12v electric systems.

This horizontal fuel pump is the same quality as the original pump.
Make sure you also replace the spacer to prevent leakage, as this is essential for protecting the pump and engine.
Baseplate gasket supplied.

This 7 piece pivot axle repair kit for AMI 6 and AMI 8 cars is high quality.
This pivot pin repair kit for one side is for restoring the connection between the suspension arm and the steering pivot.
This high quality steel set offers excellent value for money and includes:

- 1 pivot axis
- 1 bottom ring
- 1 top ring
- 2 steel washers of 2.6 mm thickness
- 1 dual-material washer, 2 mm thick
- the top cap.

This displacement kit for 602cc M28 engines in AMI 6 and AMI 8 cars - 74mm - compression 8.5 is original quality.

Made in France, this BRETILLE displacement kit is compatible with all AMI 6 and AMI 8 cars with M28 engines.
The 8.5 compression is the original compression for 2cv saloons.

It includes the 2 liners, the 2 pistons and the piston rings already fitted in the factory.

This epoxy painted rim for AMI 6 and AMI 8 cars - pinkish grey - AC140 is high quality.

This 4Jx15" rim is a quality remanufacture and is compatible with all models of AMI 6 and AMI 8 cars.
It has pinkish grey epoxy paint - AC140 which is standard on AMI 6 and AMI 8 cars from 1969.

The epoxy paint is much more resistant to knocks and scratches so this quality rim is good for perfect compatibility and durability.

The secondary silencer for AMI 6 and AMI 8 with M4 and M28 engines is compatible with all AMI 6 and AMI 8 models.
This under-body silencer is suspended under the body by 2 rubber rings.It is connected to the gooseneck or outlet tube by 2 36mm clamps. We advise you to use quality clamps to avoid any exhaust leakage.
!!! Not compatible with AMI 6 produced before June 1963 !!!

This round 12v 3 pin aluminium indicator unit for AMI 6 and AMI 8 cars is true to the original.

The round indicator unit is compatible with all AMI 6 and AMI 8 cars with 12V systems.
Made of aluminium, it connects with 3 flat lugs:
- sign +-X-B = more power
- C-L sign = front and rear indicators
- R-P sign = dashboard light.
It is adaptable on many old vehicles.

This painted rim for AMI6s and AMI8s (04/1961-03/1979) - pinkish grey - AC140 is faithful to the original.

The rim for Meharis is a quality remanufacture and compatible with all models of 2cv cars and derivatives.
It is painted pinkish grey - AC140 available as standard on 2cv cars and derivatives from 1969.

This NANKANG CX668 135/80R15 73T tyre for AMI6s and AMI8s offers excellent value for money.

Radial tyre for 2cvs for better performance and a modern grip on all AMI 6 and AMI 8 cars.

Can be mounted with valves or tubes.

This 125-135 R15 inner tube for AMIs is superior quality.

It is compatible with all models of 2cv cars and derivatives.

This premium breather for AMI is true to the original breather.

This exceptional quality breather is compatible with all 2cv cars and derivatives with 435 or 602cc engines.

This clutch kit for AMI 6 and AMI 8 cars from 1970 to 1979 - 18 splines disc and 3 finger mechanism is faithful to the original, and is compatible with AMI 8 cars from 1970 to 1979 with centrifugal or classic clutches.

This kit includes:
- 3-finger mechanism
- a clutch release bearing
- clutch disc

Check for compatibility by counting the number of splines on your clutch disc shaft.