Troubleshooting

ACCUMATE 6 and 12 Volt charger (select your voltage).

Once plugged in, the AccuMate 6/12 maintains your battery at the correct voltage to prevent sulfation for the duration of the vehicle's inactivity.

Features:
- charging current: 1.2 A
- for batteries from 4Ah to 75Ah, classic lead/acid in 6 and 12V
- for Gel and MF batteries in 12V
- no risk of overcharging. Totally safe for vehicle electronics. No sparking.
Safe, long-term battery maintenance. Automatic switch-off in the event of a short-circuit or if the battery is disconnected.

Supplied with a set of waterproof SAE permanent connectors and a set of alligator clips for all types of battery.

Perform diagnostics, recover, charge, test and maintain 12 V batteries to an optimum standard automatically. This device has an automatic desulphation cycle.
Enables the service life of your battery to be extended by 400%

Specifications:
- for standard, gel and AGM-MF batteries, with round cells
with a nominal capacity of 7.5 Ah to 120 Ah
- output current (bulk charge): 4 A
- dimensions: 190 x 75 x 56 mm
- weight: 600 g
- length of input and output cables: 2 metres

Supplied with a set of permanent connectors resistant to adverse conditions and a set of battery crocodile clips.

This Optimate 6 charger and charge maintainer is ideal for recovering heavily discharged and sulphated 12-volt batteries with very fast charging times.
Charging, recovering and maintaining your 12V waterproof battery is done in 9 automated steps. 
What is battery regeneration? 
The principle is to break up the lead sulfate crystals that have formed over time, by sending strong electrical impulses.
The resonance thus created weakens and dissolves this deposit, which is harmful to your battery's operation.
The OPTIMATE 6 charger enables you to recover a sulfated battery when it is not mechanically damaged or corroded. 

The OPTIMATE 6 charger automatically adapts to the size of the battery, thanks to its integrated Ampmatic microprocessor, and optimizes its charging up to 144Ah.

Features:
- for STD / AGM / GEL batteries with nominal capacities from 3 Ah to 144 Ah
- no risk of overcharging. Totally safe for vehicle electronics. Spark suppression. 
Long-term battery maintenance in complete safety. 
Automatic switch-off in the event of a short-circuit or if the battery is disconnected.
- output current (ground load): 5 A

Suitable for all types of 12V vehicles (motorcycles, quad bikes, jetskis, cars, motorhomes, boats, etc.).

BOOSTER 12 V - 3500 A

Le seul Homologué par les plus grands constructeurs. Coupe circuit de sécurité. Inversion accidentelle des polarité sans conséquence pour le véhicule : signalée par voyant et signal sonore, protection extrême.

Interrupteur de puissance permet de mettre les pinces en place hors tension, évite les arcs, protège l'électronique des véhicules. Chargeur "MULTIZONE": durée de vie des batteries du BOOSTER augmentée et charge rapide.
Cordon pour prise allume-cigare fourni.

Caractéristiques technique :

VL Tension de service : 12 V
Courant maximum : 3500 A
Courant de démarrage : 1150 A
Capacité de la batterie : 23 Ah
Protection contre les surtensions :oui
Interrupteur de puissance : oui
Alarme contre les inversions de polarité : oui
Fusible: non
Dimension du câble: 1,30 m
Batterie : 1 x 12 V techHD AGM
Poids : 10,46 kg

This LED light from TOOLATELIER is complementary to the traditional warning triangle and yellow vest, providing a quick warning of a vehicle immobilized in the middle of the night. This flash distress lamp, also known as an emergency lamp , is shock, vibration and water-resistant.

The products of this emergency lamp:

Center lamp white LED illumination
12 LEDs in 360° arrangement
Ultra-bright red emergency light, visible up to 1.6 km
High-strength plastic with soft plastic screen
Waterproof design
Magnetic back to stick to a metal body part

Features:

Dimensions: (Ø) 11 cm x (h) 4 cm
Weight: 200 g
Supplied with 3 AAA storage batteries, which may need to be replaced quickly to ensure correct operation.

Operating modes:

Rotating flashing LEDs: 25 hours
LEDs flashing briefly four times in succession: 25 hours
LEDs flashing briefly once: 80 hours
LEDs flashing alternately: 25 hours
4 LED flashlight: 30 hours

This permanent battery cable, allows visual control of the battery's state of charge (12V lead-acid).

Technical details:
- 3 LED (0, 1/2, v)battery status display for all 12 Volt batteries, with a 4th LED (vv) for sealed AGM batteries

TheOptimate 7 allows you to recover heavily discharged and sulphated 12-volt lead-acid batteries.
Thanks to the Ampmatic microprocessor, it is able to differentiate between a battery that needs recharging and one that needs recovery.
The choice of automotive pros for its simplicity and efficiency!

Features:
- For STD/AGM/GEL batteries with nominal capacity from 3 to 400Ah.
- Output current: 10A

The OptiMate 7 Ampmatic is THE smartest "buttonless" battery charger for standard or high-performance 12V batteries for your motorcycle, car/pick-up, boat or camper.
Automatically charge, test and maintain 12V lead-acid AGM, GEL, EFB or STD starter or deep-cycle batteries of any size, at any temperature.
The only "10 Amp" automatic charger with temperature control!
Voltage is set higher when it's cold, lower when it's hot!


Ampmatic charge control automatically adjusts current according to battery size.
A small battery receives less charge, a large one more! It saves "dead" sulphated batteries from as little as 0.5V.
The unique pulse absorption mode optimizes battery performance.
All cells are brought up to the same capacity.
Intelligent OptiMate 24-7 maintenance guarantees more power, longer life, whatever your battery!

TECMATE connector cable between your battery connection and your TECMATE/OPTIMATE charger.

To connect on your dashboard or other

OptiMate 5 charger, tester and maintainer can be used to recover discharged and sulphated 6V & 12V lead-acid batteries.

Just connect it to your battery, the charger will then carry out the diagnostic and charge your battery automatically!

Features:
- Charging Amps: 4A (6 Volts) / 2.8A (12 Volts)
- For STD, AGM and GEL batteries, from 8 to 120Ah (up to 192Ah for 6V)
- Totally safe for the vehicle and the battery, no risk of overcharging.

OPTIMATE OP1 VOLTMATIC 6 and 12 Volt charger  
Once plugged in, the AccuMate 6/12 maintains just the right voltage for your battery to prevent sulfation while the vehicle is inactive.

Completely safe long-term battery maintenance. Automatic cut-out in case of a short circuit or if the battery is disconnected.

Comes with a set of SAE waterproof permanent connectors and a set of crocodile clips.

Plastic jerrycan for fuel with spout. It has a capacity of 20 litres.
It comes with a level graduation for easy filling.

US-type galvanised metal fuel jerry can
Capacity: 5L

The jerry can may be black or dark green, depending on thesupplier's delivery The colour cannot be chosen when placing your order.

Plastic fuel jerry can with flexible pouring hose
Capacity: 5L
Practical: the hose is stored inside the can.

Plastic fuel jerry can with flexible pouring hose
Capacity: 10L
Practical: the hose is stored inside the can.

US-style galvanised steel fuel can
Capacity: 10L

US-style galvanised steel fuel can
large capacity
Capacity: 20L

Porsche official fuel can.
Embossed PORSCHE logo and inscription, original Porsche item.

Rigid 5 litre plastic bottle with pouring tube.
This spare can comes with an anti-spill towel.

This compressor with a white directional LED light is ideal to inflate car, motorcycle and bicycle tyres, balloons, mattresses, inflatable boats and any other inflatable object.

For example, it will inflate a car tyre in 3 minutes and an air mattress for one person in 2 minutes.

For easy use, the programmable digital gauge stops automatically at the required pressures and stores this pressure for the next time the compressor is used.

Its digital screen, 48 mm wide x 48 mm high with measurements in PSI, BAR, KPa, is pleasant to use offering optimised pressure readings with a status bar to keep a trace in any condition.

The air pipe is flexible and extra long, 70 cm, with a compartment to provide easy access, specially designed to reduce bending.

it is delivered with a screw valve fitting, a tyre inflation valve, a 3.3 m long power supply cable, a power socket protected with a 12V fuse and ten adapters.

This reducer delivers a constant output pressure of 6.2 bar regardless of the input pressure.

It prevents excessive working pressure and is suitable for most pneumatic tools. Very convenient, it saves energy and increases the life of pneumatic tools.

To use this tool, it is not necessary to add a pressure gauge.

Maximum inlet pressure. 10 bar (145 PSI)
Outlet pressure: constant at 6.2 bar (90 PSI)
Accuracy: 10%
Flow rate: 1300 l/min (45 CFM)
Inlet thread: 6.3 mm (1/4")
Outlet thread: 6.3 mm (1/4")