Inlet manifold

PMO 40x37mm tall intake pipes for Porsche 911 with K-Jetronic configuration

Dimensions:

- Carburetor-side diameter: 40mm
- Cylinder head diameter: 37mm

Kit contents:

- 2 intake pipes
- 6 gaskets
- 12 mounting studs, bolts and washers

Electric heated ammission pipe sleeve original or original type for VW Combi Bay Window from 1968 to 1979:
- All engines Type 1
It is possible to adapt it on other amission pipes if the diameter and length allow it.

This kit enables 3 Weber 45 DCOE carburettors to be fitted on the following versions:
- DB 4
- DB 5
- DB 6

Consists of 3 sections.

Supplied without assembly kit.

These parts are replicas of the originals and may require adjustments.

This kit enables 2 Weber DCOE carburettors to be fittedon the following version :
- Toyota 4AG engine with normal ports (52 x 30 mm)

Consists of 1 section.

Supplied without assembly kit.

These parts are replicas of the originals and may require adjustments.

CSP (Germany) short aluminum pipes. Specially designed for a Type 4 engine in a Cox with Porsche cooling cap and turbine, also ideal for a 914-4. Optimized maximum flow with a diameter adjusted to 48 mm. Plenty of material available on the staves to allow them to be reworked as required. Supplied with German quality studs, screws and gaskets.

For 2 Weber IDF or Dellorto DRLA 48 mm carburetors
For Type 4 engines with 3 mounting holes on cylinder heads.

This spacer enables a Solex 31 Pict carburettor to be mounted on a 34 mm intake pipe.
Gaskets and screws supplied.

CB Performance intake pipes for mounting 2 Weber IDA carburetors on Type 1 double-entry cylinder heads. Sold in pairs.

Features:
Straight pipes, to promote intake flow (offset carburetors)
Special casting with lots of material on the cylinder head side, to enlarge and polish the ducts.

This kit enables 2 Weber DCOE carburettors to be fitted on the following version:
- Opel Manta 2.4L

Consists of 2 sections.

Supplied with the assembly kit.

These parts are replicas of the originals and may require adjustments.

Pipes for T1 engine with single-intake cylinder heads
Designed to be fitted on Weber 34 ICT type caburettors

Short, straight CSP (Germany) aluminum intake pipes, ideal for maximizing intake flow (offset carburetors).
Diameter adjusted by 40 mm.
Reinforced , wider bases with more material to allow reworking of the duct fit with cylinder heads if required.

For 2 Weber IDF, Dellorto DRLA or Empi HPMX carburetors
Fits Type 1 engines with dual intake.

PMO 46x41mm intake pipes in standard size for Porsche 911 with Motronic configuration

Dimensions:

- Carburetor-side diameter: 46mm
- Cylinder head side diameter: 41mm

Kit contents:

- 2 intake pipes
- 6 gaskets
- 12 mounting studs, bolts and washers

Aluminum intake pipe (with gaskets) for 2 Weber DCOE carburetors for Triumph TR3 and TR4.

The intake pipe is delivered with the complete linkage to mount the 2 Weber carburetors.

This kit enables the fitting of 2 Weber DCOE carburetors for the following models:
- Triumph TR3
- Triumph TR4

Pipes for T1 engine with dual-intake cylinder heads
Designed to be fitted on Weber 34 ICT type caburettors

Center pipe for 30/31 PICT carburetor

For 1300 AR engines with dual intake and dual heater.

This manifold is equipped with double reheating, with a smaller internal diameter than the single reheating model. The VC40302 side pipes cannot be mounted on it (large diameter).

Inlet piperetainer.
Mounting: under carburetor / crankcase.

For VW Cox, Split combi and Karmann Ghia
With 30hp cast foot engine

Metal gasket between intake manifold and cylinder head.
Need 2, sold individually.

For VW :
- Cox, Karmann-Ghia, Combi
engines : 1300

PMO 46x42mm tall intake pipes for Porsche 911 with K-Jetronic configuration

Dimensions:

- Carburetor-side diameter: 46mm
- Cylinder head diameter: 42mm

Kit contents:

- 2 intake pipes
- 6 gaskets
- 12 mounting studs, bolts and washers

CSP (Germany) inclined aluminum pipes, take up cylinder offset to align twin carburetors.
Diameter adjusted to 40 mm.
Supplied with German-quality studs, screws and gaskets.

For 2 Weber IDF, Dellorto DRLA or Empi HPMX carburetors
Fits Type 1 dual intake engines.

Aluminum intake pipes with special curve for Porsche turbine clearance if required.

For 2 Weber IDF, Dellorto DRLA or Empi HPMX 36 / 40 / 44 mm carburetors on Type 4 engines.

CSP short intake pipes in aluminium for Porsche 914-4 :

- 914-4 1.7 - 80 hp (022-W) from 1970 to 1973
- 914-4 1.7 - 80 hp (022-EA) from 1972 to 1973
- 914-4 1.7 - 72 hp (022-EB) from 1972 to 1973
- 914-4 1.8 - 85 hp (021-AN) from 1974 to 1976
- 914-4 1.8 - 76 hp (022-EC) from 1974 to 1976
- 914-4 2.0 - 95 hp (039-GA) from 1973 to 1974
- 914-4 2.0 - 100 hp (039-GB) from 1973 to 1976
- 914-4 2.0 - 88 hp (039-GC) from 1975 to 1976

For two 40 mm Weber IDF or Dellorto DRLA carburettors, they offer an optimized maximum flow with a diameter adjusted to 40 mm. Lots of material available on the staves to allow them to be reworked as needed.

Supplied with German quality studs, screws and gaskets.