Suspension plates

Theseadjustable suspension blades replace the original ones and allow height adjustment of the rear suspension without removing the torsion bars.
For VW Cox (08/1959-) with trumpet rear axle fitted with 553 mm long torsion bars.
From chassis No. 2 528 668->

Mounting with 2 silentblocs 2" (51 mm) for outside (ref.VJ511024 not supplied) and 48 mm for inside (VJ511025)

2 Complete sets of 9 torsion bars for upper and lower front suspension tubes. Original VW quality.

For :
- VW Combi Split, 03/1955 ->07/1967
from chassis No. 20-117 902->
- VW Combi Bay Window, 08/1967 ->07/1979
from chassis N° 218 000 001->

Right or left front leaf spring supportscrew for Volkswagen Golf 1 Caddy.
Dimensions: M12x1.5x110mm
Part number 31 on the drawing.
This product is sold individually.

Front and rear mounting boltnut for left or right suspension leaf for Volkswagen Golf 1 Caddy.
Dimensions: M12x1.5
Part numbers 30 and 32 on diagram.
This product is sold individually.
You'll need 1 nut at the front and 2 nuts at the rear of each leaf, for a total of 6 nuts per vehicle.

Rear leaf spring silent-block for VW LT from 1996 to 2006.Silent-block inner diameter: 12mmNeed 3 per side, i.e. 6 per vehicle.

Left or right rear strut for G50 transmission on Porsche 911 type G from 1987 to 1989 :
- 911 Carrera 3.2 from 1987 to 1989
- 911 Turbo 3.3 from 1987 to 1989
This product is intended exclusively for vehicles fitted with the G50transmission, and can be used with all strut-compatible torsion bars.
Sold individually: 2 quantities required for one car.
Depending on the supplier, the millimeter scale for height adjustment may or may not be engraved on the product.

These adjustable suspension blades replace the original ones and allow height adjustment of the rear suspension, without removing the torsion bars.
For VW Cox (09/1952 -07/1959) with cardanic rear axle , but fitted with original torsion bars, length 627 mm.
Chassis no. 397 023 ->2 528 667.
On some models, you'll need silentblock covers with shims for 1302 / 1303 (VS03100).

Please measure the length of your torsion bars before ordering. Assembly with 2 silentblocs 2" (51 mm) for outside (ref.VJ511024 not supplied) and 48 mm for inside.

Original-type suspension blade (non-adjustable), right- or left-hand mounting,
sold individually.

For VW Cox (09/1952-07/1959)
with trumpet rear axle
torsion bars length 627mm.

For VOLKSWAGEN LT28 to LT35.

Left or rightstrut for Porsche 924 2.5 S from 1986 to 1988 :
- 924 2.5 S - 150 hp (M44.07/M44.08) from 1986 to 1987- 924 2.5 S - 160 hp (M44.09/M44.10) from 1988
With adjustment scale on suspension leaf.
Dichromated steel.
Sold individually: 2 quantities needed for one car.

Original type suspension blade (non-adjustable), Fitted on left or right-hand side, sold per unit.

For Beetle from 08/1959->
with rear axle with flared tubes
553 mm long torsion bars.
From chassis no. 2 528 668->

Genuine right or left rear suspension leaf support screw for Volkswagen Golf 1 Caddy.
Dimensions: M12x1.5x110mm
Part number 29 on diagram.
Requires 2 screws per leaf, i.e. 4 screws per vehicle.
This product is sold individually.
Original Volkswagen part.

Impergomleaf spring clamp for Fiat 500 all models (1957-1975)
Fits all Fiat 500 models, N, D, F, L and R
2 clamps are required per leaf spring.

Impergomleaf spring silentblock for Fiat 500 N, D, F, L and R (1957-1975)
This rubber silentblock is inserted at each end of the leaf spring.
Original quality part
Sold individually
For models listed below:- Fiat 500 N from 1957 to 1960- Fiat 500 D from 1960 to 1965- Fiat 500 F from 1965 to 1968- Fiat 500 L from 1968 to 1972- Fiat 500 R from 1972 to 1975

Rubberfront suspension buffer for Fiat 500 N, D, F, L and R (1957-1975)
This leaf spring buffer is located at the ends of the suspension leaf, on the upper part.
Sold individually
For models listed below:- Fiat 500 N from 1957 to 1960- Fiat 500 D from 1960 to 1965- Fiat 500 F from 1965 to 1968- Fiat 500 L from 1968 to 1972- Fiat 500 R from 1972 to 1975

Left or rightstrut for Porsche 968 :
- 968 3.0 - 240hp (M44.43/M44.44) from 1992 to 1995- 968 Club Sport 3.0 - 240hp (M44.43) from 1993 to 1995
With adjustment scale on suspension leaf.
Dichromated steel.
Sold individually: 2 quantities needed for one car.

Suspension blade type original (non-adjustable), Right or left hand mount,
sold individually.

For VW Combi Split (03/1955-07/1967)
with trumpet rear axle

These adjustable suspension blades replace the original ones and allow height adjustment of the rear suspension, without removing the torsion bars. Sold in pairs.
Silentblock covers with shims for 1302 / 1303 (VS03100) are required on some models.

For VW Beetle from 09/1967->
Chassis: since N° 118 071 440->
Equipped with torsion bars, length 552 mm

This rear blade lowering kit for Volkswagen Caddy mk1 (1979-1992) is made by MECATECHNIC.

Made in Europe from the finest materials, this lowering kit for Caddy Mk1 was designed by MECATECHNIC 's sales and product teams on the basis of an assembly carried out on the vehicle of an enthusiastic employee.
Depending on the number of blades, 2 or 4, and their wear (has it been driven a lot loaded or not), this kit allows a lowering of 40 to 60mm of the rear axle, the addition of shims of thickness 10, 20 or 30mm allows to lower the axle up to 90mm.

It includes :
- two perforated locking plates (for re-centering the rear axle) - Stainless steel 304 - 10mm
- two lowering spacers - Aluminium 6082
- four U-bolt leaf spring clamps - 180mm - M12 with lock nuts

Rear torsion bar mounting tubes for VW Combi Split from 08/1959 to 07/1967.